--ifref=nr    interface references by Interface Number (default)
 --ifref=ip                     ... by Ip Address
 --ifref=eth                        ... by Ethernet Number
 --ifref=descr                      ... by Interface Description
 --ifref=name                       ... by Interface Name
 --ifref=type                       ... by Interface Type

 --ifdesc=nr       interface description uses Interface Number (default)
 --ifdesc=ip                        ... uses Ip Address
 --ifdesc=eth                       ... uses Ethernet Number
 --ifdesc=descr                     ... uses Interface Description
 --ifdesc=name                      ... uses Interface Name
 --ifdesc=catname                   ... uses CatOS Interface Name
 --ifdesc=alias                     ... uses Interface Alias
 --ifdesc=type                      ... uses Interface Type

 --if-filter=f     Test every interface against filter f to decide wether
                   or not to include that interface into the collection.
                   Currently f is being evaluated as a Perl expression
                   and it's truth value is used to reject or accept the
                   interface.
                   (Experimental, under development, might change)

 --if-template=templatefile
                   Replace the normal target entries for the interfaces
                   with an entry as specified by the contents in the file
                   templatefile.  The file is supposed to contain Perl
                   code to be executed to generate the lines for the
                   target in the configuration file.
                   (Experimental, under development, might change)

 --host-template=templatefile
                   In addition to creating targets for a host's interfaces
                   do also create targets for the host itself as specified
                   by the contents in the file templatefile.  The file is
                   supposed to contain Perl code to be executed to generate
                   the lines for the host related targets (such as CPU,
                   ping response time measurements etc.) in the config-
                   uration file.
                   (Experimental, under development, might change)

 --global "x: a"   add global config entries

 --no-down         do not look at admin or opr status of interfaces

 --show-op-down    show interfaces which are operatively down

 --zero-speed=spd  use this speed in bits-per-second as the interface
                   speed for all interfaces that return a speed of 0
                   via ifSpeed/ifHighSpeed.  100Mbps = 100000000

 --subdirs=format  give each router its own subdirectory, naming each per
                   "format", in which HOSTNAME and SNMPNAME will be
                   replaced by the values of those items -- for instance,
                   --subdirs=HOSTNAME or --subdirs="HOSTNAME (SNMPNAME)"

 --noreversedns    do not reverse lookup ip numbers

 --community=cmty  Set the default community string to "cmty" instead of
                   "public".

 --enable-ipv6     Enable IPv6 support, if the required libraries are
                   present. Numeric IPv6 addresses must be enclosed
                   in square brackets, e.g. public@[2001:760:4::1]:161

 --use-16bit       Use 16bit SNMP request IDs to query all routers.

 --snmp-options=:[<port>][:[<tmout>][:[<retr>][:[<backoff>][:<ver>]]]]

                   Specify default SNMP options to be appended to all
                   routers following.  Individual fields can be empty.
                   Routers following might override some or all of the
           options given to --snmp-options.

 --dns-domain=domain
           Specifies a domain to append to the name of all
           routers following.

 --nointerfaces    Don't do generate any configuration lines for interfaces,
                   skip the step of gathering interface information and
                   don't run any interface template code.

 --interfaces      Generate configuration lines for interfaces (this is the
                   default).  The main purpose of this option is to negate
                   an --nointerfaces appearing earlier on the command line.

 --help            brief help message
 --man             full documentation
 --version         print the version of cfgmaker

 --output=file     output filename default is STDOUT